The core of a transformer is laminated because :-
- ratio of voltage in primary and secondary may be increased
- energy losses due to eddy currents may be minimised
- the weight of the transformer may be reduced
- rusting of the core may be prevented.
The Correct Option is B
Solution and Explanation
The core of a transformer is laminated to minimize the energy losses from eddy currents. This reduces the interference of the primary coil with the secondary coil and thus, the energy transfer becomes efficient. When the transformer core heats up, the energy is lost due to the eddy currents. This is electrical energy given up in the form of heat. To prevent this, the transformer core is laminated.
Also Read: Power Transformers
Top NEET Physics Questions
A constant voltage of 50 V is maintained between the points A and B of the circuit shown in the figure. The current through the branch CD of the circuit is :
- NEET (UG) - 2025
- Physics
- Current electricity
AB is a part of an electrical circuit (see figure). The potential difference \(V_A - V_B\), at the instant when current \(i = 2\) A and is increasing at a rate of 1 amp/second is:
- NEET (UG) - 2025
- Physics
- Electromagnetic Induction and Inductance
- The kinetic energies of two similar cars A and B are 100 J and 225 J respectively. On applying brakes, car A stops after 1000 m and car B stops after 1500 m. If \(F_A\) and \(F_B\) are the forces applied by the brakes on cars A and B, respectively, then the ratio \( \frac{F_A}{F_B} \) is:
- NEET (UG) - 2025
- Physics
- Work and Kinetic Energy
A full wave rectifier circuit with diodes (\(D_1\)) and (\(D_2\)) is shown in the figure. If input supply voltage \(V_{in} = 220 \sin(100 \pi t)\) volt, then at \(t = 15\) msec:
- NEET (UG) - 2025
- Physics
- Semiconductor Diode
- A microscope has an objective of focal length \(f_o = 2\) cm and an eyepiece of focal length \(f_e = 4\) cm. The tube length of the microscope is \(L = 40\) cm. If the distance of distinct vision of eye is \(D = 25\) cm, the magnification in the microscope is:
- NEET (UG) - 2025
- Physics
- Optical Instruments
Top NEET Transistors Questions
- The electron concentration in an $n$-type semiconductor is the same as hole concentration in a $p$-type semiconductor. An external field (electric) is applied across each of them. Compare the currents in them.
- NEET (UG) - 2021
- Physics
- Transistors
- The input resistan ce o f a silicon transistor is $100 \,\Omega$ B a se current is changed by $40 \,\mu A$ which results in a change in collector currently by $2 \,m A$ . This transistor is used as a comm on emitter amplifier with a load resistance o f $4 \,k\Omega$ The voltage gain o f the amplifier is
- NEET (UG) - 2012
- Physics
- Transistors
- The correct relation for $\alpha, \beta$ for a transistor
- NEET (UG) - 2000
- Physics
- Transistors
- The part of the transistor which is heavily doped to produce large number of majority carriers is
- NEET (UG) - 1993
- Physics
- Transistors
Top NEET Questions
A constant voltage of 50 V is maintained between the points A and B of the circuit shown in the figure. The current through the branch CD of the circuit is :
- NEET (UG) - 2025
- Current electricity
- Frogs respire in water by skin and buccal cavity and on land by skin, buccal cavity and lungs.
- NEET (UG) - 2025
- Animal Physiology
Which of the following statements are true?
A. Unlike Ga that has a very high melting point, Cs has a very low melting point.
B. On Pauling scale, the electronegativity values of N and C are not the same.
C. $Ar, K^{+}, Cl^{–}, Ca^{2+} and S^{2–}$ are all isoelectronic species.
D. The correct order of the first ionization enthalpies of Na, Mg, Al, and Si is Si $>$ Al $>$ Mg $>$ Na.
E. The atomic radius of Cs is greater than that of Li and Rb.
Choose the correct answer from the options given below:- NEET (UG) - 2025
- Inorganic chemistry
AB is a part of an electrical circuit (see figure). The potential difference \(V_A - V_B\), at the instant when current \(i = 2\) A and is increasing at a rate of 1 amp/second is:
- NEET (UG) - 2025
- Electromagnetic Induction and Inductance
- The kinetic energies of two similar cars A and B are 100 J and 225 J respectively. On applying brakes, car A stops after 1000 m and car B stops after 1500 m. If \(F_A\) and \(F_B\) are the forces applied by the brakes on cars A and B, respectively, then the ratio \( \frac{F_A}{F_B} \) is:
- NEET (UG) - 2025
- Work and Kinetic Energy
Concepts Used:
Transistors
Transistor
A transistor is a type of semiconductor device that can be used to both conduct and insulate electric current or voltage. A transistor basically acts as a switch and an amplifier. In simple words, we can say that a transistor is a miniature device that is used to control or regulate the flow of electronic signals.
Parts of a Transistor:
A transistor is a combination of three terminals made of semiconducting materials that help in making a connection to an external circuit and allow current to flow. The three terminals are:
- Base: The base activates the transistor. It is thin and lightly doped. It is put in the centre of the transistor.
- Emitter: The emitter is the negative terminal of the transistor. It is heavily doped and is moderately sized.
- Collector: The collector is the negative terminal of the transistor. It is located on the right side of a transistor and is moderately doped. It is larger than the emitter.
Read More: Difference Between NPN and PNP Transistor
Types of Transistors:
A transistor is a type of electronic device which is formed by p-type and n-type semiconductors.
NPN Transistor
- NPN transistor is a type of Bipolar Junction Transistor.
- In this, electrons are major current carriers, and minor ones are holes.
- Their arrangement is in such a way that N-type doped semiconductors are separated by the layer of P-type doped semiconductors which is a thin layer of material embedded between them.
- Emitter Current = Collector Current + Base Current
PNP Transistor
- PNP transistor is also a type of Bipolar Junction Transistor.
- In these, holes are the major source that carries current, and electrons are minor.
- Their arrangement is in a way that P-type doped semiconductor is separated by N-type doped semiconductor material which is a thin layer.
- Emitter Current = Collector Current + Base Current
Read More: Characteristics of a Transistor
Configurations of a Transistor:
Using the three types of configuration can be used to design any transistor circuit. The three types of configuration of a transistor are:
- Common Emitter Transistor
- Common Base Transistor
- Common Collector Transistor
Common Emitter (CE) Configuration of a Transistor
In Common Emitter Configuration, the transistor’s emitter terminal will be connected common between the output terminal and the input terminal.
Input Characteristics
- Variation of emitter current (IB) with Base-Emitter voltage (VBE) when Collector-Emitter voltage (VCE) is held constant.
- Rin = ΔVBE/ΔIB | VCE = Constant
Output Characteristics
- Variation of collector current (IC) with Collector-Emitter voltage (VCE) when the base current (IB) is held constant.
- Rout = ΔVCE/ΔIC | IB = Constant
Current Transfer Characteristics
- The variation of the collector current (IC) with the base current (IB) when the collector-emitter voltage (VCE) is constant.
- α = ΔIC/ΔIB | VCB = Constant
Common Base (CB) Configuration of a Transistor
In Common Base Configuration, the transistor’s base terminal will be connected common between the output terminal and the input terminal.
Input Characteristics
- Variation of emitter current (IE) with Base-Emitter voltage (VBE) when the Collector Base voltage (VCB) is held constant.
- Rin = ΔVBE/ΔIE | VCB = Constant
Output Characteristics
- Variation of collector current (IC) with Collector-Base voltage (VCB) when the emitter current (IE) is held constant.
- Rout = ΔVCB/ΔIB | IE = Constant
Current Transfer Characteristics
- The variation of the collector current (IC) with the emitter current (IE) when the Collector Base voltage (VCB) is constant.
- α = ΔIC/ΔIE | VCB = Constant
Common Collector Configuration of a Transistor
In Common Collector Configuration, the transistor’s collector terminal will be connected common between the output terminal and the input terminal.
Input Characteristics
- Variation of emitter current (IB) with Collector-Base voltage (VCB) when the Collector Base voltage (VCB) is held constant.
Output Characteristics
- Variation of emitter current (IE) with Collector-Emitter voltage (VCE) when the base current (IB) is held constant.
Current Transfer Characteristics
- The variation of the collector current (IE) with the base current (IB) when the Collector-Emitter voltage (VCE) is constant.